Why Does My Circuit Breaker Keep Tripping?
A breaker that trips is doing its job. Understanding which of three faults it is reporting tells you how seriously to take it.
A tripping breaker is not a malfunction. It is a protective device operating exactly as designed, and it is telling you something. The useful question is what.
There are three common answers, and they have quite different implications.
1. Overload
The circuit is being asked to carry more current than it is rated for. This is the most benign cause and usually the easiest to identify: it tends to happen when several heavy appliances are used at once, and it tends to happen consistently under the same conditions.
Kitchens are the classic case. A kettle, a toaster, a microwave and an air fryer on the same circuit will, between them, exceed what that circuit was designed for. The board is not faulty; the demand has outgrown the installation.
The fix is either changing how the load is distributed or adding circuit capacity — which is one of the more common reasons a kitchen gets additional circuits during a refit.
2. Short circuit
Live and neutral have come into direct contact. This produces a very large current very quickly, and the breaker operates almost instantly.
Short circuits are usually caused by physical damage: a nail or screw through a cable, a damaged flex, water ingress, or a failed appliance. They are not subtle, and they do not fix themselves. A circuit that trips instantly every time it is reset has a short circuit somewhere, and it needs finding.
3. Earth leakage
This is what trips an RCD rather than an MCB. Current is finding a path to earth — through damaged insulation, moisture, or a person.
Earth leakage is the most important category to take seriously, because the fault it detects is the one that injures people. It is also the most likely to be intermittent, because moisture and deterioration vary with conditions.
Narrowing it down yourself
If an RCD is tripping, there is a simple process worth trying before calling anyone:
- Unplug everything on the affected circuits.
- Reset the RCD.
- Reconnect items one at a time, leaving a gap between each.
If it trips when a particular appliance goes back on, that appliance is the likely culprit. Kettles, washing machines, immersion heaters and outdoor equipment are frequent offenders, because heating elements and moisture both cause earth leakage as they deteriorate.
If it trips with nothing connected, the fault is in the fixed wiring — and that needs testing rather than trial and error.
Cumulative leakage
One case worth knowing about: several appliances can each have a small, harmless amount of earth leakage, and together they can add up to enough to trip an RCD. Nothing is faulty as such, but the total exceeds the threshold.
This shows up as a board that trips unpredictably with no single culprit, and it is one of the arguments for individual RCBOs rather than one shared RCD covering half the property.
What not to do
Do not repeatedly reset a breaker that keeps tripping. Do not replace a device with a higher-rated one to stop it operating. Both remove protection without removing the fault, which is the worst of both outcomes.
And if a breaker will not reset at all, stop. That circuit has a fault present right now.
When to call
Call if the fault is in the fixed wiring rather than an appliance, if it is intermittent and you cannot pin it down, if there is any smell of burning or any discolouration at the board, or if a breaker will not reset.
Intermittent faults take longer to find, and the single most useful thing you can do is keep a note of when it trips — the weather, the time, what was running. That pattern frequently narrows the search considerably. Our fault finding work starts from exactly that kind of information.
Keep reading
Related guides
What an EICR Is, and What the Codes Actually Mean
Electrical Installation Condition Reports are full of codes that decide whether you have a problem. Here is how to read one.
When Should You Call an Electrician?
Some electrical problems can wait. Some genuinely cannot. Here is a practical way to tell which is which.
Electrical Fault Finding: How a Fault Is Actually Traced
Fault finding is a methodical process, not a hunt. Understanding it explains why it is charged separately from the repair.